Homekit multicast. I have used the discovery app on my Mac

Homekit multicast. I have used the discovery app on my Mac and I can see the HomePods showing. Multicast packets seem to be an important part of HomeKit networking and occasionally the UniFi switch/router was incorrectly filtering packets. Normally DNS would require a DNS server to host and resolve name records, but by using mDNS this can be done totally on the local network, specifically using Aug 15, 2023 · Are there any settings or things to enable/check to ensure mDNs / Bonjour / Multicast is working correctly. Feb 29, 2024 · Once that is setup, on the network where you have your docker host and your IoT network check the the IGMP snooping and Multicast DNS checkboxes. One Wi-Fi network had Multicast and Broadcast Control enabled. Multicast is also required for the automatic search of the KNX IP gateway. A huge class of problems with unresponsive devices seem to be related to router-specific behaviors around how multicast traffic is handled, without which HomeKit’s use of the mdns (“Bonjour”) protocol cannot work properly. 0. Devices implementing mDNS need to listen to these packets and respond where appropriate. See if there is a solid basic IP link I’m suspecting it’s more likely to be a multicast issue, but I’ve not heard of anyone having issues like that between AiMesh nodes to date. Multicast von und zu VLAN 1 (LAN / PRIVAT) und VLAN 2 (IOT) mDNS spielt bei der HomeKit Kommunikation eine wichtige Rolle May 23, 2024 · In your Network settings, enable Multicast DNS and IGMP Snooping for the involved VLANs: That’s a short one for Unifi (I’m on Network version 8. Needless to say, all my HomeKit stuff is acting much better (perfect) now. If you are using a UniFi system (like the UDM Pro), you will need to make sure in the UniFi settings that Multicast DNS is enabled, IGMP Snooping is enabled, and Block LAN to WLAN Multicast and Broadcast Data is disabled. This not only protects your network. Enable efficient multicast forwarding (IGMP Snooping): Enable. responds to pings but sometimes/always unresponsive in homekit. 4ghz and 5ghz SSID's and these are my Wi-Fi settings Enable multicast routing (IGMP Proxy): Enable. HomeKit device connected to WIFI2. Ports Sep 7, 2024 · Hello! I have GL-SFT1200 (Opal) here. The network must support IPv4 addresses. Apr 6, 2021 · Besides configuring the firewall for data to move freely from one zone to another, UDP multicast stops at the subnet (to prevent DDoS or something like that). Packets need to be relayed to other subnets. If you are using a Linksys Velop router, go into the Velop admin portal in your browser (not the app). I had them on 5GHz, now switched to 2. In the wifi configurations for your regular-use wifi and your IoT wifi check the Multicast Enhancement box. GL-SFT1200 in repeater mode connected to this open wifi. The multicast address 224. I needed a specific rule allowing my homekit hub to talk to homebridge on certain ports, as we as the following settings enabled: Apple services ports: Ports range 49152 - 65535 and Port 3722 Network settings: IGMP snooping and Multicast DNS - Enabled Enable multicast routing (IGMP Proxy): Enable. I don't have any evidence or sources but I believe having static IP addresses for your devices improves their network reliability, and make them easier to work with homebridge. Fortigate GUI „Multicast Enhancement“ IGMPv3 im UniFi Controller muss nicht aktiviert werden, wenn Multicast Forwarding auf der ForitGate verwendet wird; 2. After reading this I started looking into my UniFi home network setup and ended up turning off “Enable multicast enhancement (IGMPv3)” for each wireless network. Sep 16, 2018 · For the record: If you have a Unifi network and you activate the HomeKit functionality on Home Assistant, remember to add the MAC address of the host where HA is installed to the list of the wired hosts that are allow to broadcast on the Wi-Fi network. HomeKit does not work with IPv6-only networks. 23. Jun 9, 2022 · I started having problems in the past month or so where HomeKit showed everything as ‘no response’. The below docker-compose. MultiCast Policy. Jun 30, 2021 · multicast-ttl-notchange: enable. I dont think this is a lack of range issue considering some of these products were right near the router. Hope this tip helps! Jun 3, 2018 · mDNS is a tricky protocol – essentially it’s DNS, but instead of going to a name server for resolution, devices using mDNS send out a multicast packet to the network and wait to see who replies with the answer. VPN connection from GL-SFT1200 to my home router (Unifi HomeKit enabled routers enable you to set firewall security for your HomeKit devices. After disabling the setting, in the last 7 days, I haven’t had any “No Response” issues. Nov 21, 2023 · HomeKit uses Apple’s Bonjour service for zero configuration service discovery, which in turn uses multicast DNS (mDNS) and DNS Service Discovery to publish and broadcast these services. This is found under your Unifi network setup: settings --> Wireless Networks --> (edit your Wi-Fi network) --> Advanced Options --> Multicast . 12 and port 3671 are used for this. My setup looks like this - I have free/open wifi network (WIFI1) in remote location where I have my HomeKit device located (camera). Optional: set static IP addresses for your HomeKit devices. 251 (IPv4) and ff02::fb (IPv6) as well as port 5353 are used for this. 113) users struggling with the connection between the Home Assistant Bridge and Apple Homekit. For my internal network Multicast DNS was not enabled which was the worst problem. First thing I noticed was the Wi-Fi Multicast Enhancement was enabled on a few Wi-Fi networks. Custom Wifi network (WIFI2) created on GL-SFT1200 for my HomeKit device. My router is a RT-AC86U for reference. yml file does the following things: sets up an nginx-proxy container The multicast addresses 224. Dec 9, 2019 · When the devices stop responding to HomeKit have you tried setting up a ping from the router to them or from your phone/pc connected to the main router. 4 to see if it makes a difference, I have dedicated channels for the 2. edit 1 Made a couple edits to be more clear which ones might be optional. I don’t have any evidence or sources but I believe having static IP addresses for your devices improves their network reliability, and make them easier to work with homebridge. This also helps protects your iCloud if you’re using HomeKit Secure Video or some other HomeKit service that ties to your iCloud. 1. edit 2 more testing, crossed off the items that don't affect homekit stability. Feb 19, 2018 · Enable multicast routing (IGMP Proxy): Enable; Enable efficient multicast forwarding (IGMP Snooping): Enable; Optional: set static IP addresses for your HomeKit devices. I have three. npghvv bzz mujcos nxufue jeazs rxkcqc jlsh ntdiyl micycv our